Frag tank/ sump in basement

[bandit]

I'm setting up a 50gal frag tank/sump in my basement. Does anybody no if a quite one 6000 will pump 10 foot rise 20 foot length

[Wooki]

The max height for the quiet one 6000 is 11.5 ft.  So you are looking at a optimal flow rate of about 150 gph at 10 feet.  See the chart below from J&L

http://www.jlaquatics.com/images/flowcharts/quietone_6000.jpg

Add a few turns, and more lateral distance, and you might end up with less than 100 gph. 

So it seems it would not be powerful enough.

W

[bandit]

Thanks humm I'm only running a 1200 at 4 feet so my current sump turnover is 150 gal/hr, I like slow low but 100 gal is too slow

[bandit]

I guess a mag drive 12 or 18 I'm just worried the 18 would be to much flow??

[Wooki]

Bandit

I recall now that reef central has a head loss calculator where they programmed in the published data from manufacturers. 

http://www.reefcentral.com/index.php/head-loss-calculator

It does height, number of valves, 90 degree turns, etc....  It should be helpful for your planning.

W

[Aquaticfinatic]

I have a mag 18 pushing maybe 10' at most and is just trickling out of the returns. I should have gone for the 24 but going up in size doubles the power consumption. If I had to do it again I would pay a little more for a better more efficient pump. Go DC if you can afford it :0) quiet ones are not the most energy efficient ones out there FYI. If you want to stick with them make sure the pump has HH on it which stands for high head. It'll push a lot higher than one without. Hope this helps 

[bandit]

I have a mag 18 pushing maybe 10' at most and is just trickling out of the returns. I should have gone for the 24 but going up in size doubles the power consumption. If I had to do it again I would pay a little more for a better more efficient pump. Go DC if you can afford it :0) quiet ones are not the most energy efficient ones out there FYI. If you want to stick with them make sure the pump has HH on it which stands for high head. It'll push a lot higher than one without. Hope this helps 

thanks do you have any elbos is it a solid line, I find your better with vinyl and long gradual bends.

[bandit]

Bandit

I recall now that reef central has a head loss calculator where they programmed in the published data from manufacturers. 

http://www.reefcentral.com/index.php/head-loss-calculator

It does height, number of valves, 90 degree turns, etc....  It should be helpful for your planning.

W

Thanks

[az]

check octopus water blaster pumps, lots of flow at any height, low wattage too. mag drive would do good too, quiet1 dont do too well at certain height, we needed a 9000 to push 8' high.

[Aquaticfinatic]

thanks do you have any elbos is it a solid line, I find your better with vinyl and long gradual bends.

I have half and half. Where it goes through the floor and to the returns are 3/4 pvc but the rest down to the pump is hose. I had a q1 4000hh that just couldn't do it plus run hot. Flexible PVC is the way I'm going next time for sure. I have 2 elbows in each of the two return lines i have plus split into 2 1/2 loc lines. That may slow it a little but not much.

[Severum]

Poseidon pumps are the way to go. Mine pushes 15' with a 40' run and is so quiet you have to touch it to tell its on. Does run a little hot, but water gets cold in the basement.

I think you might have seen it when over trading frags a while ago.

[Aquaticfinatic]

Poseidon pumps are the way to go. Mine pushes 15' with a 40' run and is so quiet you have to touch it to tell its on. Does run a little hot, but water gets cold in the basement.

I think you might have seen it when over trading frags a while ago.

Is that internal or ex?

[Severum]

external

[bandit]

Poseidon pumps are the way to go. Mine pushes 15' with a 40' run and is so quiet you have to touch it to tell its on. Does run a little hot, but water gets cold in the basement.

I think you might have seen it when over trading frags a while ago.

I will look into those pumps I like the external idea gives me much more room, hw long have you had the Poseidon and what model??

[bandit]

Well It looks like the poseidons are discontinued?? 

[bandit]

Looks like I'm going to go with the iwaki md water pumps wd40lt very good riveiws

http://www.marinedepot.com/Iwaki_WMD_Water_Pump_(American_Motor)_Up_to_1000_Gallons_Per_Hour_External_Aquarium_Pumps-Iwaki-IK1223-FIWPEPZT-vi.html

[Severum]

I use the PS4. Yes I guess they are dicontinued by now. I found mine here on OVAS for about $100 or so. Been working for several years without any issues.

I found a PS4 online...
http://www.fishtanksdirect.com/browseproducts/Velocity-Poseidon-PS4-Titanium-Aquarium-Pump.html

Flow charts for the various models would determine which is best for your application. I needed the most flow at the highest head.
http://www.marinedepot.com/pumps_poseidon_information-ap.html

[bandit]

thanks for the link, unfortunatly you cant order it LOL

[bandit]

I ended up buying a iwaki today http://www.bulkreefsupply.com/iwaki-md-30rt-japanese-motor-510-gph.html

Hope it works has 17 foot head only I measured 10 feet  I need

[Severum]

Well good luck with it. Let us know how it goes.